ESU 59827 - LokPilot 5 micro DCC, 6-pin direct, retail, gauge N, TT

ESU 59827 - LokPilot 5 micro DCC, 6-pin direct, retail, gauge N, TT

 

Technical details

The LokPilot 5 micro DCC is the "twin" of the LokPilot 5 micro. At just 8.0mm x 7.0mm and a thickness of just 2.4mm (at the capacitor: 2.9mm), it is a pure DCC decoder, just small enough to fit into very small locomotives of nominal sizes Z, N or TT. However, this sacrifice of flexibility is rewarded with a lower price.
LokPilot 5 micro DCC decoders are available with all common interfaces. The versions with Next18 or PluX16 interfaces are slightly larger with a base area of 13.0mm x 9.2mm, but have 2 additional function outputs.

Operating modes

The LokPilot 5 micro DCC is a "pure" DCC decoder. 14 to 128 speed levels are as natural as 2- and 4-digit addresses. Up to 32 functions can be triggered. Thanks to RailComPlus®, the decoders register fully automatically with a suitable digital control center.
It can handle all DCC programming modes and thanks to RailCom®, the CV values on the main track can be read out with suitable control centers. There are auxiliary registers for control centers that can only program CVs from 1-255.
The LokPilot 5 micro DCC decoder recognizes the Märklin® braking sections as well as ZIMO® HLU / ZACK commands or the Lenz® ABC system. Braking with DCC brake modules or with direct current is also possible. In addition, it also stops with a Selectrix® brake diode. An ABC shuttle train automation enables automatic commuting between two stations.
The LokPilot 5 DCC decoder can be used on analogue direct current railways. The maximum speed can be set separately.
The decoder switches between the operating modes fully automatically "on the fly". Usually nothing needs to be set.

Functions

We know that you want your locomotives to be as realistic as possible. That's why we have equipped the LokPilot 5 micro DCC with an astonishing number of function outputs. The versions with 6-pin or 8-pin wiring harness offer 4 amplified function outputs, each with 180mA output current, as well as two logic level outputs for servos or Susi. The versions with Next18 or PluX16 interface have a total of 6 amplified outputs and two logic level outputs. All important light functions are available. The brightness of each output can be set separately. The decoder can automatically apply and release when uncoupling for ROCO®, Krois® and Telex® couplings.

Motor control

The motor control of the LokPilot 5 micro DCC has been fundamentally improved again. A variably adjustable PWM clock frequency of 10kHz to 50kHz ensures super quiet operation, especially with bell-shaped armature motors - the typical "humming" is a thing of the past. The load control can now be adapted to difficult cases with up to 10 CVs. The unique "autotune" function enables the decoder to be automatically calibrated to the motor. With up to 0.75A motor current, the LokPilot 5 micro DCC decoder delivers enough power for the intended application scenarios.

Operational safety

If required, a PowerPack can be connected to the LokPilot 5 micro to bridge dirty track sections.

Protection

The motor output and the function outputs are of course protected against overload. We want you to enjoy your decoder for as long as possible.

 

 

 

Characteristics:

Manufacturer:	ESU
Item number:	59827
number of pieces:	1 piece
EAN:	4044645598276
Product Type:	decoder
Electricity system:	DC
operation mode:	DCC / AC Digital
interface:	6 pin NEM 651 directly
Digital decoder:	Yes
Connections::	6 pin NEM 651 directly
length:	8.0mm
Width:	7.0mm
Height:	2.4mm
Operating modes:	DCC
Connection technology:	6 pin NEM 651 directly
Function output (total):	4
Current limit. Fu-Off:	180mA
Logic level outputs:	2
LED outputs:	Light effects
Servo outputs:	2
SUSI:	Yes
Dir. Energy Saving Connection:	retrofittable
Weight:	0.7g
Age recommendation:	14 years and older
WEEE No.:	DE62103961
BattG registration number:	21002525