Doehler & Haass DH10C-1 - Vehicle decoder (Gen2)

Doehler & Haass DH10C-1 - Vehicle decoder (Gen2)

 

Technical details

Vehicle decoder DH10C for SX1, SX2, DCC and MM (2nd generation)

Product features and functions
For optional operation with digital systems according to SelecTRIX 1 and 2 or according to DCC format
In digital operation, the last programmed system is used (it does not switch automatically!)
SelecTRIX 1 31 speed levels, 100 addresses
SelecTRIX 2 127 speed levels, 10,000 addresses, 16 additional functions
DCC short addresses (1-127), long addresses (0001-9999), with 14, 28, 126 speed levels
Latest generation load control, resulting in particularly smooth control behavior
Various control variants for optimal adaptation to the motor
Internal 127 speed levels
Adjustable motor frequency (low frequency, 16 kHz, 32 kHz)
Block section operation with simple diodes in digital mode
Light and function outputs dimmable
Shunting mode
Motor, light and track connections electronically interchangeable
All function outputs freely programmable
Temperature protection
Reset function for DCC and SX2
Decoder update capability
The DH10C vehicle decoder supports braking with asymmetrical digital voltage (four diodes in series and one diode anti-parallel, Lenz ABC), slow travel (with suitable brake modules) and bidirectional communication (locomotive address feedback in DCC operation, RailCom®).

For SX1 programming, a SUSI module connected to the supply voltage (VS) or a connected buffer must be removed. It is sufficient to interrupt the supply voltage (red wire for SUSI) for the time of SX1 programming. The SX2 or DCC programming is not affected by this.

Our proven vehicle decoder DH10C is now available in the 2nd generation after product maintenance has been completed and offers many advantages:
greatly reduced dimensions (12.7 * 8.9 * 1.4 mm)
higher overall load capacity and higher motor current (1.5 A)
AUX3 and AUX4 as amplified function outputs (1.0 A)
AUX5 and AUX6 as unamplified function outputs (alternative to the SUSI interface)
around five times the buffer capacity (therefore longer contact faults can be overcome without data loss)

Due to the reduced length of the decoder, we can now offer the new connection variant DH10C-4 for the first time, which has a six-pin pin strip directly on the decoder. In future, this should preferably be used for models with an NEM 651 interface. (The connection variant DH10C-1 with ribbon cable for Minitrix models will of course also remain in the range.) We also offer the new connection variant DH10C-2, which has a separate six-pin pin strip. This is ideal for models where the installation space for the decoder is not directly next to the interface.

 

 

 

Characteristics:

Manufacturer:	Doehler & Haass
Item number:	DH10C-1
number of pieces:	1 piece
Product Type:	Vehicle decoder
track:	neutral
Digital decoder:	Yes
Connections::	Ribbon cable (NEM 651 Minitrix)
Current (V):	30V
length:	12.7mm
Width:	8.9mm
Height:	1.4mm
Operating modes:	SX1, SX2, DCC, MM, DC
Connection technology:	Ribbon cable
Continuous current:	1.5A
Current motor output duration:	1.5A
Function output (total):	6 + 2 x light
Current limit. Fu-Off:	AUX1+2 300 mA (dimmable), AUX3+4 1.0 A each
LED outputs:	150 mA each (dimmable)
Servo outputs:	No
SUSI:	Yes, if AUX5+6 is off
Dir. Energy Saving Connection:	No (possible via VS (+) and GND (-))
Speaker output:	No
Sound memory:	No
Age recommendation:	14 years and older
WEEE No.:	DE 28016265